KitchenAid dishwasher F8E4 error code
- Dishwasher
KitchenAid dishwasher F8E4 means the leak sensor in the base pan detected water — the dishwasher stops and may run the drain pump continuously. A loose inlet connection, worn door gasket, or oversudsing that spills over the door causes most F8E4 codes before the sensor itself fails. Pull the dishwasher out slightly and check for water in the drip tray under the tub.
Reviewed August 2025 · sources below
Safe to keep using?
Stop using
Severe overheating requires stopping use until the cause is identified.
- • Unplug the appliance before inspection.
- • Turn off the water supply before disconnecting hoses.
- • Do not continue using the appliance until the cause is identified.
4 product recalls may apply
Brand-level matches — verify your model.
Show
4 product recalls may apply
Brand-level matches — verify your model.
- Notice
CPSC, Whirlpool Corporation Announce Recall of Dishwashers
Feb 2005 · Confirm your model
- Notice
Dishwasher Recalled by Whirlpool
May 1996 · Confirm your model
- Notice
Whirlpool Will Retrofit Below-Counter Dishwashers
Jul 1989 · Confirm your model
- Notice
Dishwasher Model Number Correction for Whirlpool Modification
Aug 1988 · Confirm your model
Next step
Still seeing F8E4?
Show a photo or describe the symptom. Answer a few safety-first questions and see whether a part is needed.
Free guided checks · No account required · Don’t open live electrical, gas, or refrigerant equipment
How to fix F8E4
- Unplug the dishwasher and remove the front toe kick to access the base pan.
- Soak up water in the drip tray with towels — the float sensor resets when the pan is dry.
- Inspect inlet hose connections at the valve and door gasket for tears or gaps along the bottom seal.
- Check for oversudsing — use dishwasher detergent only and avoid rinse-aid spills into the tub.
- Restore power after the pan is dry — F8E4 should clear. Replace the sensor only if it trips with a dry pan.
Call a pro when: Call a technician if water returns in the pan after drying, or you cannot find the leak source.
What F8E4 means
Water detected in the drip tray — empty the tray and check for leaks.
Likely causes
Many codes resolve with cleaning, resetting, or reconnecting.
Check: Power-cycle the appliance and check for obvious blockages or loose connections.
Est. cost: $0–$0
Wear or electrical failure of an internal part.
Check: If basic checks fail, the faulty component likely needs replacement.
Est. cost: $0–$75
Professional assistance recommended
This issue may be unsafe for DIY repair. Follow the safety guidance above and contact a qualified technician.
Questions about F8E4
What does F8E4 mean on a KitchenAid dishwasher?
F8E4 is a leak-detected fault — water in the base pan triggered the safety float.
How do I reset KitchenAid F8E4?
Dry the base pan completely, fix the leak source, then restore power.
Why does my dishwasher keep draining with F8E4?
The control runs the drain pump to empty the tub when a leak is detected — dry the pan to stop it.
Do I need a new sensor for F8E4?
Rarely — fix the actual leak first. Replace the sensor only if F8E4 returns with a dry pan.
KitchenAid F8E4 on specific models
Other KitchenAid Dishwasher codes
Prevent this problem next time
- Follow manufacturer maintenance schedule
- Address small issues before they worsen
Sources
Manufacturer meaning
Water detected in the drip tray — empty the tray and check for leaks.
FixApplianceCode guidance
Start with basic checks for KitchenAid F8E4 before ordering parts.
Source type: Part database
Source: ModelPartFinder + FixApplianceCode editorial
Last reviewed: 2026-10-23
Repair guidance is for informational purposes only. We do not guarantee that any fix will resolve your issue, and you assume all risk when following these steps. Terms & disclaimer
As an Amazon Associate I earn from qualifying purchases. Some links may also earn other retailer commissions, at no additional cost to you. Affiliate disclosure