LG error codes
Browse all known LG error codes. Pick your appliance, or click any code for fix steps and parts.
Top LG error codes
Most searched codes with full fix guides and compatible parts.
Washer error codes
Dryer error codes
- CLChild lock is enabled.
- d75Exhaust duct is about 75% restricted — lint or a crushed vent is slowing airflow.
- d80Exhaust duct is about 80% restricted — clothes take too long to dry.
- d90Exhaust duct is about 90% restricted — clean the lint filter and vent now.
- d95Exhaust duct is about 95% blocked — a fire and overheat risk until the vent is cleared.
- nPNo current detected at the heater — often a 240V outlet, breaker, or power-cord wiring issue.
- PSWrong voltage at the power cord — the white and red wires may be reversed on the terminal block.
- dEDoor error (often shown as dE) — the door is not fully closed, or the lint filter is not seated.
- FOLint filter is out — reinsert the filter before starting a cycle.
- HSHumidity sensor error — the dryer may run a very long cycle until the sensors are cleaned.
- PFPower failure — the last cycle was interrupted by a power loss.
- tE1Thermistor error — the dryer cannot read incoming air temperature.
- tE2Thermistor error during a steam cycle — extra humidity cooled the duct too fast.
- tE3Thermistor error — the dryer cannot read exhaust temperature.
- gASGas dryer is not receiving gas — check the supply valve and line.
- AddSteam feeder needs water — fill the drawer with tap water before a steam cycle.
- E13Hybrid condensing dryer drain hose is kinked, clogged, or frozen.
Refrigerator error codes
- IFIce maker fan or freezer fan error.
- FFFreezer evaporator fan not running — often ice buildup or a failed fan motor.
- CFCondenser fan error — coils may be dirty or the fan motor failed.
- rFRefrigerator compartment fan error — fresh food side may warm up.
- dHDefrost heater fault — frost can build up and block airflow.
- FSFreezer temperature sensor error.
- rSRefrigerator compartment sensor error.
- dSFreezer defrost sensor error.
Oven / Range error codes
- F1Oven thermistor error — the control cannot read oven temperature.
- F2Oven thermistor error — the sensor circuit is open or shorted.
- F3Oven thermistor error — temperature reading is out of range.
- F9Keypad or display error — metal or water may be sitting on the control.
- F10Display communication error.
- F11Low voltage — the range is not getting enough power.
Dishwasher error codes
- AELeak sensor detected water in the base — the dishwasher keeps draining to protect the floor.
- E1Leak detected (same family as AE) — water reached the float switch in the base pan.
- IEWater inlet error — the tub is not filling. Check the shutoff valve and kinked inlet hose.
- OEDrain error (often shown as OE) — the tub is not emptying. Clean the filter and straighten the drain hose.
- FEOverflow / fill error (often shown as FE) — too much water in the tub. The unit will keep draining.
- HEHeater error — the dishwasher cannot heat wash water.
- tEThermistor error — the dishwasher cannot read water temperature.
- LEWash motor error (often shown as LE) — the cleaning motor is not running normally.
- bEBubble / suds error — too much foam, usually from regular dish soap.
- nEImpeller or Vario motor error — a dish may be blocking the spray arm, or the diverter is stuck.
- CEMotor communication error — often appears with LE when the wash pump cannot start.
- F31Dynamic Heat Dry fan motor is not running.
- F35Dynamic Heat Dry temperature cannot be measured — heater or sensor fault.
- F37Auto Open Door did not operate — something may be blocking the door.
Microwave error codes
- LOCChild lock is enabled — the control pad is locked.
- DOORDoor is open or the door switch is not making contact.
- E10Sensor error — humidity or gas sensor reading is out of range.
- F1Microwave thermistor / sensor error (often shown as F1).
- F2Microwave sensor error (often shown as F2).
- F4Microwave sensor error.
- F5Microwave sensor error.