Maytag dryer F22 error code
- Dryer
Maytag dryer F22 indicates the door switch circuit is open — the dryer will not start or continue because it does not detect a closed door. A bent strike, worn switch plunger, or loose wire at the door harness causes most F22 codes on WED4815EW-class dryers. Press the switch by hand at the door frame — you should hear a crisp click before ordering a board.
Reviewed August 2025 · sources below
Safe to keep using?
Stop using
Severe overheating requires stopping use until the cause is identified.
- • Unplug the appliance before inspection.
- • Do not continue using the appliance until the cause is identified.
3 product recalls may apply
Brand-level matches — verify your model.
Show
3 product recalls may apply
Brand-level matches — verify your model.
- Notice
Whirlpool Recalls Stacked Commercial Clothes Dryers Sold Under the ADC Brand Due to Fire Hazard (Recall Alert)
Sep 2023 · Confirm your model
- Notice
CPSC, Whirlpool Announce Recall of Washer and Gas Dryer Units
Jul 2002 · Confirm your model
- Notice
Gas Dryers Repair by Maytag Appliances
Jan 1997 · Confirm your model
Next step
Still seeing F22?
Show a photo or describe the symptom. Answer a few safety-first questions and see whether a part is needed.
Free guided checks · No account required · Don’t open live electrical, gas, or refrigerant equipment
How to fix F22
- Unplug the dryer and inspect the door strike alignment — the door should compress the switch plunger fully when closed.
- Listen for a click when pressing the door switch manually at the upper door frame.
- Check the door switch harness for loose connectors behind the front panel.
- Replace the door switch (W10169310 on many models) if the plunger does not click or tests open at all door positions.
- Restore power and press Start — F22 clears when the switch circuit closes.
Call a pro when: Call a technician if F22 persists after switch replacement or you see melted wiring at the door harness.
What F22 means
Exhaust thermistor open — the dryer cannot read exhaust temperature.
Buy the replacement part
Likely causes
Many codes resolve with cleaning, resetting, or reconnecting.
Check: Power-cycle the appliance and check for obvious blockages or loose connections.
Est. cost: $0–$0
Wear or electrical failure of an internal part.
Check: If basic checks fail, the faulty component likely needs replacement.
Est. cost: $0–$100
Professional assistance recommended
This issue may be unsafe for DIY repair. Follow the safety guidance above and contact a qualified technician.
Questions about F22
What does F22 mean on a Maytag dryer?
F22 is a door switch fault — the control does not see a closed door.
How do I reset Maytag dryer F22?
Close the door firmly, check the strike, and replace the switch if the plunger failed. No software reset fixes a bad switch.
What part fixes Maytag F22?
Usually the door switch (W10169310). The main board is rarely the cause.
Can a broken strike cause F22?
Yes — if the door does not push the switch plunger, the dryer thinks the door is open.
Maytag F22 on specific models
Other Maytag Dryer codes
Prevent this problem next time
- Follow manufacturer maintenance schedule
- Address small issues before they worsen
Sources
Manufacturer meaning
Exhaust thermistor open — the dryer cannot read exhaust temperature.
FixApplianceCode guidance
Start with basic checks for Maytag F22 before ordering parts.
Source type: Part database
Source: ModelPartFinder + FixApplianceCode editorial
Last reviewed: 2026-10-24
Repair guidance is for informational purposes only. We do not guarantee that any fix will resolve your issue, and you assume all risk when following these steps. Terms & disclaimer
As an Amazon Associate I earn from qualifying purchases. Some links may also earn other retailer commissions, at no additional cost to you. Affiliate disclosure